ここから本文です
TWO:
Classification by type of system
1natural circulation external heating pipe type
2natural circulation calandria type
3forced circulation type
4falling-film type
5rising film type
6jacket type
7coil type
Classification by method of operation
1single effect evaporator system
2multiple effect evaporator system
3auto-vapor mechanical compression system
4auto-vapor ejector compression system
5multistage flash system

After taking into consideration of the physical and chemical property of solutions, the desired design conditions, and available utilities, we select the most suitable type of system by utilizing our years of experience and excellent results.
In addition, we can offer designs and manufacturing services that take into careful consideration compactness, energy-efficiency, and automatization.

THREE:Near Haccourt, by the bank of the Meuse, I noticed a terrible glare of fire and dense smoke. It was an alarming sight, and made me fear the direst things. I considered for a moment whether I should go there or not, fearing that I had already taxed my nerves too much. Yet, I made up my mind to go, and by a side-way got to the Meuse, near Vis. German engineers were busy here laying telephone wires, and an officer stopped me, threatening me with his revolver. It was obvious that they were no longer accustomed to see civilians on that road. After having examined my passport and seeing that I was a Netherland journalist, he became very friendly, and politely urged me not to go farther.

While standard calandria type evaporation systems are widely used as the typical concentration evaporator by the various food and chemical industries, we have delivered many of those systems as finishing concentration evaporators especially for sugar solutions and starch syrups.

THREE:Drilling, more than any other operation in metal cutting, requires the sense of feeling, and is farther from such conditions as admit of power feeding. The speed at which a drill may cut without heating or breaking is dependent upon the manner in which it is ground and the nature of the material drilled, the working conditions may change at any moment as the drilling progresses; so that hand feed is most suitable. Drilling machines arranged with power feed for boring should have some means of permanently disengaging the feeding mechanism to prevent its use in ordinary drilling.
  • Enables flexible operation with little influence from variations in load and raw solution concentrations because of an adequate amount of solution being held within the system. These systems are also suitable for batch type burning evaporators.
  • Concentrations can be controlled within product specifications by the cascade control using the concentrations of concentrated solution and the raw solution supply and also by the arithmetic control of raw solution concentrations, etc. (Result for sugar solutions: 75±0.2wt%)
  • High-viscosity solutions and solutions that may crystallize can also be utilized by installing a propeller in the evaporator as a forced circulation system.
THREE:These divisions of machinery will next be treated of separately, with a view of making the classification more clear, and to explain the principles of operation in each division. This dissertation will form a kind of base upon which the practical part of the treatise will in a measure rest. It is trusted that the reader will carefully consider each proposition that is laid down, and on his own behalf pursue the subjects farther than the limits here permit.

This is a process example of a device that continuously and simultaneously concentrates two types of waste liquid with a single high-efficiency steam compressor.

THREE:There was only one that he cared to see, and that was Hetty. In a curious way the girl's goodness and purity appealed strongly to him. As to his future he cared nothing. He wanted to know if anything had been seen of Leona Lalage, and when Hetty replied to the contrary he seemed to be greatly astonished.
  • By evaporating the steam using a mechanical compressor and reusing it, almost no heating steam is alomost required except the time of start-up, so large energy savings can be expected.
  • By combining with a thin film falling heat exchanger that does not raise the boiling point due to the liquid depth, it is possible to utilize the temperature difference of the compressor at the maximum.
  • Since the residence time and heating time are short and the holding amount is small, starting and stopping can be performed in a short time.
  • It will prevent scale adhesion in the can that the evaporator is divided into two parts, and that the supply of the undiluted solution is alternately switched over a fixed period of time to perform heat concentration.